Skip to content
Circuits Gallery
  • Home
  • BasicsExpand
    • Wiring
    • Op-Amp
    • Circuitry
    • Oscilloscope
    • Conductivity
    • Components
  • MicroControllerExpand
    • Arduino
    • PIC
    • Simulation
  • ProjectExpand
    • Using 555 Timer
  • DigitalExpand
    • Communication
  • Submit Project
Circuits Gallery
Home / Basics / How to Calculate Amps For Led Lights? | Calculating Amps for LED Lights

How to Calculate Amps For Led Lights? | Calculating Amps for LED Lights

Although there are three ways to find out the amps of your lights, the easiest one is to use the basic formula of dividing power in watts (W) by the volts (V) of voltage. For example, if the wattage of the lighting fixture you’re working with is 60 and the volts are 12, divide 60 by 12 to get 5 amps.

The amperage is also important for folks who need to choose the right size circuit for their home. You can convert the amp rating of a circuit breaker to watts, but it is easier to use amps because the rating printed on a circuit breaker is presented in amps.

How to calculate amps for led lights

Procedure for Calculating Amps for LED Lights

A regular bedroom LED light of 10W draws just 0.083 Amps. Because LED lights consume less energy than incandescent bulbs while producing the same amount of light. But if you want to test how many amps are drawn by your LED, then you can use one of these three ways.

Converting Watts to Amps

You can convert watts into amps by using the power formula. The power formula, which states that I = P/E, where P is power measured in watts, I is currently measured in amps, and E is the voltage measured in volts, can be used to convert watts to amps.

In this formula, take the wattage reading of your LED light and divide it by the voltage of your home. Thus, current I in amps equals power P in watts divided by voltage V in volts. You can also use this site- Watts to Amps Conversion Calculator (thecalculatorsite.com) to measure Amps from Watts easily.

Measuring DC Amperage with An Ammeter

You have to connect an ammeter in “series” with the LED, not in parallel. In other words, you’d have to insert it between the potentiometer and the LED and act as a “wire” connecting the two. You can also use a multimeter for this operation.

Multimeters will be rated for a specific quantity of current. If you use a multimeter rated for 10 amps and then run 200 amps through it, the fuse will blow. So, you have to be careful about the ratings.

Calculating Amperage with Ohm’s Law

According to Ohm’s law, the current flowing through a resistive conductor (the LED) between two places is proportional to the voltage across the two points. In other words, the current I in amps (A) of a resistor is equal to the voltage VR=V in volts (V) divided by the resistance R in ohms (O) {I=V/R}. So, mainly to calculate amps, you’ll use Ohm’s Law:

Amps (A) = Watts (W) / Volts (V)

Let’s say you have an LED light with a wattage of 10 watts and you live in a country with a 120V electrical system.

  • Amps = 10 watts / 120 volts = 0.083 amps

So, you have to take the voltage of your home and divide it by the resistance of your LED light. The value you will get here will be the amps drawn by the LED light of your home. Watts/Volts/Amps/Ohms Calculator (rapidtables.com) – this site can help you with Ohm’s law calculations.

The Necessity of Electrical Ratings

Connecting your foodservice equipment to the incorrect voltage is the most common cause of equipment failure. If you connect your new equipment to the incorrect power supply, it will not function properly and may even be damaged.

Given the cost of outfitting your kitchen with professional equipment, you’ll want to ensure that the electrical standards are satisfied. To avoid this common error, use our voltage calculator to precisely compute amps, voltage, or watts.

Amps

Amperes, often known as amps, are units of measurement for the flow of electricity as an electric current. They specifically monitor the number of electrons that travel past a specific spot every second. A garden hose is a typical illustration used to demonstrate how amps function. 

The volume of water flowing through the hose can be compared to amps. The stronger the current, the more liters of water that flow through the hose every minute. Alternatively, as the number of electrons passing through a certain place per second grows, so do the amps.

LED Lights Turn-on Voltage

An LED’s polarization is typically between 1.8 and 3.3 volts. Depending on the hue of the LED lamp, it varies. A red LED normally loses 1.8 volts, but when the bandgap rises, the voltage drop and frequency of light increases, and a blue LED can drop from 3 to 3.3 volts.

Frequently Asked Questions

How do you calculate amps to watts?

The power formula, which states that P=I*E, where P is power measured in watts, I is the current measured in amps, and E is the voltage measured in volts, can be used to convert amps to watts. As a result, power P in watts equals current I in amps multiplied by voltage V in volts.

Conclusion

When measuring the amps of an LED light, you should keep in mind that a usual home in America utilizes 120V. On the other hand, many European countries prefer 220-250V power supplies.

Table Of Contents
  1. Procedure for Calculating Amps for LED Lights
  2. The Necessity of Electrical Ratings
  3. Amps
  4. LED Lights Turn-on Voltage
  5. Frequently Asked Questions
  6. Conclusion

Subscribe to our newsletter

& plug into

the world of circuits

    A seasoned electronics enthusiast, Charles Clark is a key contributor to Circuits Gallery. From basic components to advanced microcontroller projects, Charles simplifies complex concepts with ease. His writings are a blend of expertise and passion, making electronics accessible to all. Whether it's circuitry or digital communication, Charles is the voice you can trust.

    Facebook Twitter Instagram

    Recent Blogs

    • How to Make A 75 To 300 Ohm Matching Transformer
      How to Make A 75 To 300 Ohm Matching Transformer? | A Step by Step Guide for You
    • How to Download Circuit Wizard? | Procedure for Downloading the Latest Version
    • What Gauge Wire from Battery to Starter
      What Gauge Wire from Battery to Starter? | Choosing the Right Wire Gauge
    • What Does 50 Milliamps Look Like on a Multimeter
      What Does 50 Milliamps Look Like on a Multimeter? | Let’s Find Out
    • How Many Watts Does a 32 Inch TV Use
      How Many Watts Does a 32 Inch TV Use? | Find Out the Required Wattage for Different Brands
    • What Size Conduit for 122 Wire
      What Size Conduit for 12/2 Wire? | Choosing the Right Conduit for Your 12/2 Wire

    Browse Categories

    • Arduino
    • Basics
    • Circuitry
    • Communication
    • Components
    • Conductivity
    • Digital
    • How To
    • MicroController
    • Op-Amp
    • Oscilloscope
    • PIC
    • Project
    • Simulation
    • Using 555 Timer
    • Wiring
    Circuits Gallery
    Join Our Community:

    Quick Links

    • About Us
    • Privacy Policy
    • Terms and Conditions
    • Submit Your Project
    • Contact Us

    Our Story

    Our journey designing innovative devices had immersed us in convoluted electronics. We realized mastery doesn't require elite degrees or industry secrets—just knowledge presented coherently. We became devoted to unraveling even quantum-complex circuits, diagram by diagram, so anyone eager to learn can unlock these secrets. By simplifying electronics fundamentals, we hope to ignite innovation in generations to come.

    © Copyright 2025 Circuits Gallery | All Rights Reserved.

    • Home
    • Basics
      • Wiring
      • Op-Amp
      • Circuitry
      • Oscilloscope
      • Conductivity
      • Components
    • MicroController
      • Arduino
      • PIC
      • Simulation
    • Project
      • Using 555 Timer
    • Digital
      • Communication
    • Submit Project
    Search